Removal of MRF24WG0A driver from Harmony v2.03b (AnEngineerWithAPlan)
Hi all, I'm disappointed that the driver for MRF24WG0A has been removed without notice from Harmony v2.03b. I don't think it's asking too much for this at least to be documented in the release notes....
View ArticlePIC32MZ CAN Driver (AHancock)
Hello all,This morning I launched into the Harmony PIC32MZ CAN driver and, how can I say this, I am underwhelmed. First my setup review:Custom board with PIC32MZ2048EFH144IDE - MPLAB X v3.35Compiler...
View ArticleUSB CDC HOST locking up (gweeper)
I've got an application using Harmony 2.03b that uses the USB in host mode for both CDC and MSD. MSD works fine, and CDC works fine *most* of the time. Under heavy CDC RX traffic workloads, the USB...
View ArticleUSART Question (Skaptor)
Would calling DRV_USART_Deinitialize(); Give me temporary port control until I initialize it again?..
View ArticleHarmony hell of the day : compiling... (jipihorn)
Hello and welcome to the wonderful world of Harmony. I used to use Harmony 1.08 and it worked, until I had the crazy idea of adding a bootloader which leads me to upgrade to Harmony V2.03. A pretty...
View ArticleQuestions regarding Harmony's v2.02b Graphics Stack (bblessing)
First the obligatory background: MPLAB X IDE v3.55XC32 v1.43Harmony v2.02bPIC32MX470F512L processorNewhaven NHD-4.3-480272EF-ASXN#-T LCDIS61WV51216BLL-10TLI external memory The reason I chose the...
View ArticleMHC Opus decoder library opus_decode() crashes when called from PIC32MZ_EF...
Was the Opus library in Harmony (v2.02b) built only for devices without an FPU? I gather that supported audio boards include the defunct PIC32MZ_EC Audio PIM, but I don't see a PIC32MZ_EF version. I'm...
View ArticleHarmony 2.03 does not save the network configurations correctly. (jipihorn)
Hello, Again and again, Harmony never ending nightmare.Today, I discovered that if you have two network configurations (say one WiFi MRF24WN and one Ethernet PIC32INT) , you save the mhc file and open...
View ArticleHow to enabled HTTP Net server ? (Emcy)
Hello, I created a new project : DHCP client, announce discovery tool, telnet server and icmp server operate.I have enabled HTTP Net server but it is impossible to open a web page => web browser...
View ArticleSQI CS0, does this work at all? (jtzeng)
Has anyone been able to get SQI1CS0 to work on a device???I can get SQI1CS1 to work just fine...
View ArticleHarmony v2.03 ProgressBarWidget causing whole screen to flash (tim.phillips)
HiI am using harmony v2.03 and have added a single progress bar to a functional display.I have a loop in my code which updates labelWidgets correctly.When I...
View ArticleUpdate to Harmony 2.03b for very new BTADK boards running audio (Tom Crosley)
I am in the group developing PIC32 applications for Harmony. We have discovered an issue that will affect only a few customers, but we didn't want to wait until the next version of Harmony (2.04) comes...
View ArticlePickit 3 harmony (mat1554)
Hi, I'd like to use PIC3MX220F032B and PicKit 3 to get an ECG signal using the pic's ADC and send the data, something as simple as possible, by USB. First, I used MCC, but I couldn't write any code to...
View ArticleUSART Driver check Receiver Idle (Memen)
How can the receiver idle state of the USART driver be checked in Harmony?I used to check the RIDLE bit of the uart module before starting transmission of a new byte. This is still possible with...
View ArticleHarmony Application Design (PICcadillyCircus)
I am new to Harmony and want to write code as the Harmony designers intended, but I am not sure when to lay out my program into different apps. For example, I am trying to read an SPI ADC, and send...
View ArticleHarmony 2.03b USB Bootloader (pcglue)
I used Harmony 2.03b to create a USB MSD bootloader for a PIC32MZ EFM, and it works. I followed the same steps to create one for the PIC32MX795F512L (it's actually the PIC32 Ethernet Starter Kit board)...
View ArticlePIC32MX75F512L ethernet problem (Akshayy)
I am using PIC32MX795F512L controller in my app.i have designed ethernet firmware as per harmony tool.i want to check whether it is working or not.I want to ping this device through my computer. I have...
View ArticleBasic LCD task (bblessing)
So I have been able to run a demo project (LCC) using MPLAB Harmony v1.11. This, of course, verified that my hardware is solid (PIC32MX470F512L, NHD-4.3-480272EF-ASXN#-T 4.3" Resistive touch screen...
View Article