Driver for SST26VF016B ? (Volker)
Hello, i want to start a project where the SST26VF016B SPI Flash will be used.So these Device is recommended for new designs, the mature SST25VF016B should not be used anymore. Exist a deathline for...
View ArticleHarmony V1.00 not ready for use - C++ gives invalid conversion errors all...
I am trying to use harmony in a c++ project and when I compile, there are all sorts of invalid conversion errors in the harmony header files! Here is one example:...
View ArticleUSB_DEVICE_EndpointWrite() and USB_DEVICE_EndpointRead() need a final...
Both USB_DEVICE_EndpointWrite() and USB_DEVICE_EndpointRead() are missing a call to OSAL_MUTEX_Unlock() for the "could not find a spare IRP" error exit...
View ArticleUSB FS OUT Endpoint Stalls under load on PIC32MX ESK (stuart lynne)
I'm implementing a test application using the USB FS support in Harmony 1.03.1, testing on the Ethernet Starter Kit.This application presents a reasonably large amount of data to be transferred in both...
View ArticleDownload link? (Xykon)
Hello, Where can I get the Harmony installer? I tried but that only gives the following: Access DeniedYou don't have permission to access...
View ArticleI2C driver DRV_I2C_BufferStatus() hangs (Ef)
Hi,I'm using a PIC32MX675 with MPLAB X 2.35 and Harmony 1.03.01. I'm trying to get the I2C drivers to work. Below is the code I'm using. This code is used to open a client instance, send data and then...
View ArticleI2C (wayne_)
I looked at the I2C example, setup I2C in Harmony and started writing my own state machine to write to the I2C. This worked fine.I then started writing the read routines and thought this would be...
View ArticleHarmony and pic32mz with sdcard (cl29200)
Hello :) I need help :)I want to use sdcard with my pic32mz.Sdcard is connected to pic with 10k resistors pullup to3.3 on sdi,sdo,CSWrite protect and card detect (for the test) is connected to gnd....
View ArticleDM320015 touchscreen problems (ToshCom)
I am trying to get the touchscreen to work but haven't had much luck again.I am using Microchip Harmony configuration setup with DM320015 GDD dev board. The display graphics works but touch isn't...
View ArticlePIC32MZ Harmony Project To Support Android BasicAccessoryDemo App (Michael...
I am struggling to understand what is the Harmony demo app to load and build for the PIC32MZ_EC_SK that will support the ready built Android App Store program from Microchip called the Basic Accessory...
View ArticleWrong link to Harmony v1.04.01 Release Notes (ematicon)
Harmony home page -> Link to MPLAB® Harmony Release Notes and Contents (v1.04.01) (141 KB):http://www.microchip.com/mplabharmony-ide-releasenotes-helpfilesopens release notes for previous...
View ArticleStrange wifi driver (Benny32)
Hello everbody, I'm working on a project with SD-Card, WiFi and external ADC (via I2C). I wrote my own functions for view things. I tested WiFi on the beginning of my application. And the driver works...
View ArticlePIC32MZ with MRF24W and TCP/IP Stack (Arcus111)
So, I am integrating a MRF24WG0MA module with a PIC32MZ on a custom board. I am using Harmony version 1.03 with MPLAB X 2.35 and XC32 1.34. The communications with the WiFi module uses SPI and when you...
View ArticleHarmony App migration 1.03 -> 1.04 (bikeoid)
I have a skeleton app in which I have defined dozens of pin and peripheral definitions via the configurator in 1.03. It generated, compiled and built in 1.03. I installed Harmony 1.04.01 and copied the...
View ArticleMissing #defines in generated code (luker)
I have a PIC32 Multimedia Expansion Board II with 4.3" WQVGA PCAP Display Board that runs a demo application.From this application's project I know that the display is using an LCC display controller,...
View ArticleBUG: _UART_4_VECTOR is not defined (muellernick)
Hi! As I don't know how to report bugs to Microchip, I post that one here:With a PIC32MX564F128H (I didn't check others), in the definition file p32m564f128h.h, the #define _UART_6_VECTOR 49 is...
View ArticleHarmony V1.00 not ready for use - C++ gives invalid conversion errors all...
I am trying to use harmony in a c++ project and when I compile, there are all sorts of invalid conversion errors in the harmony header files! Here is one example:...
View ArticleWiFi SPI Problem (wayne_)
I have WiFi on Instance 0 - SPI_ID_1It seems to work OK until I send lots of small packets. I am getting an error in drv_spi.c @ line 583if (DRV_SPI_SYS_QUEUE_AllocElementLock(pDrvObject->queue,...
View ArticleMissing DRV_I2C_WaitForStopComplete function (mmko)
Hi, Im starting to write an I2C dynamic driver,everything links fine with the exception of DRV_I2C_WaitForStopComplete and DRV_I2C_WriteByteAcknowledgedAm I miss something? Digging in the framework i...
View ArticleHarmony and graphics driver (bw64)
I'm trying to use an TFT with the ILI9341 controller within a Harmony application. I guess I will have to develop the driver if there isn't a driver already available. Is not very clear in the...
View Article